커피 장비

  

서리(Admin) 13.02.05. 22:32
댓글 1 조회 수 5587

Just back from SCAA and a post of findings and thoughts will follow.  This particular post is a bit overdue and takes precedence. I have posted about the Uber Grinder part of the Marco Uber Project a couple of times, initially where we wanted to explore the taste profiles resulting from different particle distributions and latterly about the results of trying to achieve the elusive ‘perfect’ burr.

I promised to post the grind profiles of the tests carried out. I will try to minimise the text and get straight to the plots. Everybody loves pictures! Note, all these experients were scientific analyses only – no taste comparisons were filed.

 

The-Uber-Grinder-Burr-Set.png

 

The first plot shows the Uber Grinder Burr for Marco, called type ‘M’ in the reports. The work continues to further refine this already excellent burr-set. Obvious commentary: the minimal amount of fines and height of the peak are the two key components we were after.

 

Crushing-burr-Vs-Uber-Grinder-Burr-set.png

 

The next plot compares the ‘M’arco burr with a crushing burr. Interestingly, the profile is quite close to the M burr. With marginally more fines (not good) and a marginally higher peak (good), it gives the M a run for its money. While the general consensus was a crushing burr delivers a ‘worse’ particle shape than a standard burr, it was not verified on a taste test. The belief is the extra heat generated by the crushing burr and the inferior particle shape gave the ‘M’ the win. 

 

The-Speed-Test.png

 

 

The next came the speed test, whereby the M was put through its paces at a standard 50Hz, 5Hz and 100Hz yielding 1420, 142 and 2840 revolutions per minute. The fastest speed delivered the worst plot, while the slowest speed, at 10% of standard matched the regular speed almost exactly. While grind temperatures were not measured, the slow output speed of the 142 rpm gave the win to the type ‘M’ but only just!

 

The-Accelerator-Test.png

 

Challenge number three as the introduction of the accelerator or ‘turbo washer’. Designed to get the beans into the grinding teeth quicker, the resultant graph yielded an inferior peak. Fail.

 

The-Glass-Pearl-Test.png

 

Up stepped the glass pearls. Here we played with the ‘seasoning’ of blades, a process whereby the burrs are blasted with tiny glass beads to effectively blunt the burrs slightly to give the teeth a consistent output with no ‘scraggly’ bits, if you know what I mean. Unsurprisingly, the lesser the blasting the better the profile.

 

 
The-Cast-Burr.png
 

Finally, we brought in an outsider – a cast 100mm burr. What’s there to say? Type M by a street.

 What does all this tell us: The current iteration of the Uber Grinder with type M burrs is still the best available. However, further improvement will come by minimising the ‘seasoning’ and the addition of titanium plating. I hope I didn’t break anybody’s head with all this guff.

 
 
http://marco.ie/uberproject/
profile

ABOUT ME

대한민국 No.1 커피 미디어 "블랙워터이슈" 입니다.
일반회원

댓글 1

profile

딴죽걸이

2013-02-18 15:24  #6649

역시..크래쉬 버의 강점...  일본식 그라인더가.. 브루윙에선.. 여전히 맹렬한 위세가..  

The Intelligent Dosing Ring
baratza-forte-review
Slayer Baby - 1 group machine prototype
Mechanical Paddle - GS/3 O-ring 교체
슬레이어 1 GROUP - BABY SLAYER more
슬레이어 1 GROUP - BABY SLAYER
modbar
S Filter for AeroPress Coffee Makers
The MEDIUM Espro Press
지클러에 따른 유량 세팅 : from HB article by Eric
Compare: Mazzer Coffee Grinders
Compak New Grinders - Prototype Ver. 1
Pulling Shots
Londinium I & HG One
Wilfa Svart Presisjon Coffee Brewer
Street Smarts #5: French Press 1
Where is it - Linea PB ? 4
ZPM ESPRESSO 프로토 타입 테스트
UBER GRINDER – THE GRIND OFF 1
Scottie Callaghan Dosing Tools
바라짜 바리오 + 호퍼 익스텐더